AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Powered by AMiner. Clicking this button will take you away from SciOpen.
Home Friction Article
PDF (4.4 MB)
Cite
EndNote(RIS) BibTeX
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

An improved method for evaluating the rotational speed stability of a hydro-viscous clutch in mixed lubrication

Shou-Wen YAO1,2, Qian LIU1( ), Hong-Wei CUI3, Shan-Shan FENG1
School of Mechanical Engineering, Beijing Institute of Technology, Beijing 100081, China
National Key Laboratory of Vehicular Transmission, Beijing Institute of Technology, Beijing 100081, China
School of Mechanical Engineering, Taiyuan University of Technology, Taiyuan 030024, China
Show Author Information

Abstract

Rotational speed stability is an important evaluation indicator of the performance of a hydro-viscous clutch (HVC). To improve the rotational speed stability of HVCs in mixed lubrication and the running condition of the friction pairs, the speed stability of an HVC in mixed lubrication was studied. To this end, the friction coefficients of both copper-based and paper-based friction pairs were experimentally tested using an MM1000-III wet friction machine. Theoretically, a torsional vibration model of the system is presented. The phase plane analysis method is applied to evaluate the stability of the torsional vibration model, where a critical negative gradient (CNG) is defined. The results show that the friction coefficient in mixed lubrication is an important parameter for the stability of the rotational speed. The system will be unstable when the negative gradient of the friction coefficient-slip speed is larger than the CNG. According to the definition of the CNG, suggestions regarding choice of friction pairs are made to improve the rotational speed stability of an HVC in mixed lubrication.

Keywords

hydro-viscous clutch; mixed lubrication; speed stability; negative gradient of friction coefficient-slipping speed; torsional vibration model; critical negative gradient

References

[1]
Cho J H, Schultz W W, Ceccio S L, Yoshioka T, Hiraki H. Modeling and parametric study of torque in open clutch plates. ASME J Tribol 128(2): 422-430(2006)
Crossref Google Scholar
[2]
Zhou M-S, Zhang Y. Theoretical research on hydroviscous speed-adjusting clutch in soft-start of belt conveyor. J Coal Sci Eng 11(1): 79-82(2005)
Google Scholar
[3]
Huang J-H, Fan Y-R, Qiu M-X. Effects of groove on behavior of flow between hydro-viscous drive plates. J Cent South Univ Tech 19: 347-356(2012).
Crossref Google Scholar
[4]
Sojoudi H, Khonsari M M. On the behavior of friction in lubricated point contact with provision for surface roughness. J Tribol 132 (1): 012102 (2009)
Crossref Google Scholar
[5]
Cameron T M, Devlin M T, McCombs T, Rollin A J, Tersigni S H, Jao T-C. Clutch parameter effects on torque and friction stability. SAE Technical Paper 2011-01-0722 (2011)
Crossref Google Scholar
[6]
Patir N, Cheng H S. An average flow model for determining effects of three dimensional roughness on partial hydrodynamic lubrication. ASME J Lubr Technol 100(1): 12-17(1978)
Crossref Google Scholar
[7]
Lu X B, Khonsari M M, Gelinck E R M. The Stribeck curve: Experimental results and theoretical prediction. J Tribol 128(4): 789-794(2006)
Crossref Google Scholar
[8]
Lu X B, Khonsari M M. An experimental investigation of dimple effect on the Stribeck curve of journal bearings. Tribol Lett 27(2): 169-176(2007)
Crossref Google Scholar
[9]
Wang W-Z, Liu Y-C, Wang H. A computer thermal model of mixed lubrication in point contacts. J Tribol 126(1): 162-170(2004)
Crossref Google Scholar
[10]
Wang W-Z, Wang S, Shi F H. Simulations and measurements of sliding friction between rough surfaces in point contacts: From EHL to boundary lubrication. J Tribol 129(3): 495-501(2007)
Crossref Google Scholar
[11]
Masjedi M, Khonsari M M. Film thickness and asperity load formulas for line-contact elastohydrodynamic lubrication with provision for surface roughness. J Tribol 134(1): 011503-011512(2012)
Crossref Google Scholar
[12]
Huang X G, Wei C G. Stability of oil film and output speed of hydroviscous drive affected by the pressure of control oil. J Beijing Institute Tech 10(3): 226-271(2001)
Google Scholar
[13]
Berger E J. An investigation of friction-induced vibration in automatic transmission wet clutches. Ph. D. Thesis. Purdue University, 1996.
[14]
Huron G. Numerical Simulation of SAE#2 Ma-chine Tests. SAE Technical Paper 1999-01-3617 (1999)
Crossref Google Scholar
[15]
Gao H, Barber G C, Shillor M. Numerical simulation of engagement of a wet clutch with skewed surface roughness. J Tribol 124: 305-312(2002)
Crossref Google Scholar
[16]
Greenwood J A, Tripp J H. The elastic contact of rough spheres. J Appl Mech 34:153-159(1967)
Crossref Google Scholar
Friction
Volume 3 Issue 1,
March 2015
Pages 47-55
DOI: 10.1007/s40544-014-0071-1
Cite this article:
YAO S-W, LIU Q, CUI H-W, et al. An improved method for evaluating the rotational speed stability of a hydro-viscous clutch in mixed lubrication. Friction, 2015, 3(1): 47-55. https://doi.org/10.1007/s40544-014-0071-1

610

Views

84

Downloads

4

Crossref

N/A

Web of Science

4

Scopus

0

CSCD

Altmetrics
Received: 19 May 2014
Revised: 12 July 2014
Accepted: 02 December 2014
Published: 05 January 2015
© The author(s) 2014

This article is published with open access at Springerlink.com

Open Access: This article is distributed under the terms of the Creative Commons Attribution License which permits any use, distribution, and reproduction in any medium, provided the original author(s) and source are credited.
Return