AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
Powered by AMiner. Clicking this button will take you away from SciOpen.
Home Friction Article
PDF (6.6 MB)
Cite
EndNote(RIS) BibTeX
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

High temperature lubrication performance of chlorophenyl silicone oil

Yan MENG1,2, Xiangli WEN2, Jie CHENG1( ), Pengpeng BAI2, Yonggang MENG2, Yu TIAN2( )
School of Mechanical and Electrical Engineering, China University of Mining and Technology-Beijing, Beijing 100083, China
Department of Mechanical Engineering, State Key Laboratory of Tribology in Advanced Equipment, Tsinghua University, Beijing 100084, China
Show Author Information

Graphical Abstract

Abstract

Most studies of liquid lubricants were carried out at temperatures below 200 °C. However, the service temperature of lubricants for aerospace and aeroengine has reached above 300 °C. In order to investigate the friction mechanism and provide data for high temperature lubrication, the friction and wear properties of chlorophenyl silicone oil (CPSO)-lubricated M50 steel and Si3N4 friction pairs were investigated herein. Ball-on-disk experimental results show that the lubrication performance of CPSO varies significantly with temperature. Below 150 °C, coefficient of friction (COF) remains at 0.13–0.15 after the short running-in stage (600 s), while the COF in the running-in stage is 0.2–0.3. At 200 °C and above, the running-in time is much longer (1,200 s), and the initial instantaneous maximum COF can reach 0.5. Under this condition, the COF gradually decreases and finally stabilizes at around 0.16–0.17 afterwards. This phenomenon is mainly due to the different thickness of boundary adsorption film. More importantly, the wear rate of M50 steel increases significantly with the temperature, while the wear rate barely changes at temperatures above 200 °C. The anti-wear mechanism is explained as tribochemical reactions are more likely to occur between CPSO and steel surface with the increased temperature, generating the FeCl2 protective film on the metal surface. Accordingly, FeCl2 tribochemical film improves the lubrication and anti-wear capacity of the system. At high temperatures (200–350 °C), FeCl2 film becomes thicker, and the contact region pressure becomes lower due to the larger wear scar size, so the wear rate growth of M50 steel is much smaller compared with that of low temperatures (22–150 °C). The main findings in this study demonstrate that CPSO lubricant has good anti-wear and lubrication capacity, which is capable of working under temperatures up to 350 °C.

Keywords

chlorophenyl silicone oil (CPSO)liquid lubricantanti-wearhigh temperature

References

[1]
Meng Y G, Xu J, Jin Z M, Prakash B, Hu Y Z. A review of recent advances in tribology. Friction 8(2): 221–300 (2020)
Crossref Google Scholar
[2]
Guan J. Research on rolling contact fatigue damage behavior of m50 bearing steel in aeroengine rolling bearing. Ph.D. Thesis. Harbin (China): Harbin Institute of Technology, 2019. (in Chinese)
[3]
Tang, G Z, Xu, F J, Ma, X X. Microstructure and properties of surface modified layer for M50 steel by high current pulsed electron beam. Heat Treat Met 35(7): 62–65 (2010) (in Chinese)
Google Scholar
[4]
Ge Q J, Zhang X H, Ma X X, Chen X G, Tang G Z. Tribological Properties of TiN Coated M50 Steel for High Temperature Bearing Against Sliver Coatings. Aeronautical Manufacturing Technology (Z2): 54–58 (2017) (in Chinese)
Google Scholar
[5]
Dante R C, Kajdas C K. A review and a fundamental theory of silicon nitride tribochemistry. Wear 288: 27–38 (2012)
Crossref Google Scholar
[6]
Wang L, Snidle R W, Gu L. Rolling contact silicon nitride bearing technology: A review of recent research. Wear 246(1–2): 159–173 (2000)
Crossref Google Scholar
[7]
Liu W M, Xu J, Feng D P, Wang X B. The research status and prospect of synthetic lubricating oils. Tribology 33(1): 91–104 (2013) (in Chinese)
Google Scholar
[8]
Feng D P, Weng L J, Liu W M. Progress of tribology of perfluoropolyether oil. Mocaxue Xuebao/tribology 25(6): 597–602 (2005)
Google Scholar
[9]
Wang D. Lubricating oil of future aviation engine. Synthetic Lubricants 32(4): 26–29 (2005)
Google Scholar
[10]
Zhu L Y, Chen L G, Liu H C, Lei J, Zhang N S. Tribological and corrosion behaviors of benzotriazolium ionic liquids as lubricants of steel-steel system. Tribology 34(6): 715–721 (2014) (in Chinese)
Google Scholar
[11]
Li H J, Tian P Y, Lu H Y, Jia W P, Du H D, Zhang X J, Li Q Y, Tian Y. State-of-the-art of extreme pressure lubrication realized with the high thermal diffusivity of liquid metal. ACS Appl Mater Interfaces 9(6): 5638–5644 (2017)
Crossref Google Scholar
[12]
Bai P P, Li S W, Tao D S, Jia W P, Meng Y G, Tian Y. Tribological properties of liquid-metal galinstan as novel additive in lithium grease. Tribol Int 128: 181–189 (2018)
Crossref Google Scholar
[13]
Bai P P, Li S W, Jia W P, Ma L R, Meng Y G, Tian Y. Environmental atmosphere effect on lubrication performance of gallium-based liquid metal. Tribol Int 141: 105904 (2020)
Crossref Google Scholar
[14]
Andriot M, Chao S H, Colas A, Cray S, DeBuyl F, DeGroot J V, Dupont A, Easton T, Garaud J L, Gerlach E, et al. Chapter 2—Silicones in industrial applications. Inorganic polymers: 61–161 (2007)
[15]
Ebert F J. Performance of silicon nitride (Si3N4) components in aerospace bearing applications. In Proceedings of the ASME 1990 International Gas Turbine and Aeroengine Congress and Exposition, Brussels, Belgium, 1990.
Crossref
[16]
Wang L, Wood R J K, Harvey T J, Morris S, Powrie H E G, Care I. Wear performance of oil lubricated silicon nitride sliding against various bearing steels. Wear 255(1–6): 657–668 (2003)
Crossref Google Scholar
[17]
Shi H T, Bai X T. Model-based uneven loading condition monitoring of full ceramic ball bearings in starved lubrication. Mechanical Systems and Signal Processing 139: 106583 (2020)
Crossref Google Scholar
[18]
Lin, G Y, Wang, S R, Wang, L P. Frictional performance and leakage of ball bearings lubricated by chlorphenyl silicone oil in vacuum. Tribology 29(6): 526–530 (2009) (in Chinese)
Google Scholar
[19]
Weng L J, Wang H Z, Feng D P, Pan G M, Duan Y R, Liu W M, Xue Q J. Synthesis and tribological behavior of a chlorinated-phenyl methyl-terminated silicon oil as aerospace lubricant. Mocaxue Xuebao/tribology 25(3): 254–257 (2005)
Google Scholar
[20]
Schiefer H M, Awe R W, Whipple C L. Extending the utility of silicone lubricants through structural modifications. J Chem Eng Data 6(1): 155–160 (1961)
Crossref Google Scholar
[21]
Schiefer H M, Van Dyke J. Boundary lubricating properties of fluoroalkyl silicones in bench and pump tests. S L E Trans 7(1): 32–42 (1964)
Crossref Google Scholar
[22]
Weng L J, Wang H Z, Feng D P, Liu W M, Xue Q J. Tribological behavior of the synthetic chlorine- and fluorine-containing silicon oil as aerospace lubricant. Ind Lubr Tribol 60(5): 216–221 (2008)
Crossref Google Scholar
[23]
Jiang K J, Zhang X. Lubricity of fluorosilicone. Journal of Aeronautical Materials 31(4): 81–85 (2011) (in Chinese)
Google Scholar
[24]
Lv M, Yang L J, Wang Q H, Wang T M, Liang Y M. Tribological performance and lubrication mechanism of solid–liquid lubricating materials in high-vacuum and irradiation environments. Tribol Lett 59(1): 20 (2015)
Crossref Google Scholar
[25]
Munavirov B, Black J J, Shah F U, Leckner J, Rutland M W, Harper J B, Glavatskih S. The effect of anion architecture on the lubrication chemistry of phosphonium orthoborate ionic liquids. Sci Rep 11: 24021 (2021)
Crossref Google Scholar
[26]
Wu Q. Silicone oil and lubricate. Journal of Shaanxi Normal University (Natural Science Edition) (Z01): 163–172 (1981) (in Chinese)
Google Scholar
[27]
Zhou N. Introduction of silicone polymer. Beijing: Science Press, 2000.
[28]
Dube M J, Bollea D, Jones W R, Marchetti M, Jansen M J. A new synthetic hydrocarbon liquid lubricant for space applications. Tribol Lett 15(1): 3–8 (2003)
Google Scholar
[29]
Li X, Lin F J, Du S M, Wu C C. Comparative analysis of high performance bearing steels. Heat Treatment of Metals 46(6): 14–20 (2021) (in Chinese)
Google Scholar
[30]
Khonsari M M, Ghatrehsamani S, Akbarzadeh S. On the running-in nature of metallic tribo-components: A review. Wear 474–475: 203871 (2021)
Crossref Google Scholar
[31]
Blau P J. On the nature of running-in. Tribol Int 38(11–12): 1007–1012 (2005)
Crossref Google Scholar
[32]
Wen X L, Bai P P, Meng Y G, Ma L R, Tian Y. High-temperature superlubricity realized with chlorinated-phenyl and methyl-terminated silicone oil and hydrogen-ion running-in. Langmuir 38(32): 10043–10051 (2022)
Crossref Google Scholar
[33]
Zhang C W, Peng B, Wang L Q, Ma X X, Gu L. Thermal-induced surface damage of M50 steel at rolling-sliding contacts. Wear 420–421: 116–122 (2019)
Crossref Google Scholar
[34]
Aisyah I S, Caesarendra W, Kurniawati D, Maftuchah M, Agung D, Glowacz A, Oprzędkiewicz K, Liu H. Study of jatropha curcas linn and olea europaea as bio-oil lubricant to physical properties and wear rate. Lubricants 9(4): 39 (2021)
Crossref Google Scholar
[35]
Peng H L, You X Z, Xu X M, Qiu B L, Shao Y G. Synthesis Process of Methylphenyl Silicone Resin. Insulating Materials 44(4): 16–19 (2011) (in Chinese)
Google Scholar
[36]
Li C X. Infrared spectroscopeic analysis of synthetic lubes. Synthetic Lubricants 42(4): 36–40 (2015) (in Chinese)
Google Scholar
[37]
Freedman H H. Intramolecular H-bonds. I. A spectroscopic study of the hydrogen bond between hydroxyl and nitrogen. J Am Chem Soc 83(13): 2900–2905 (1961)
Crossref Google Scholar
Friction
Volume 12 Issue 8,
August 2024
Pages 1716-1727
DOI: 10.1007/s40544-023-0827-6
Cite this article:
MENG Y, WEN X, CHENG J, et al. High temperature lubrication performance of chlorophenyl silicone oil. Friction, 2024, 12(8): 1716-1727. https://doi.org/10.1007/s40544-023-0827-6

365

Views

17

Downloads

1

Crossref

0

Web of Science

1

Scopus

0

CSCD

Altmetrics
Received: 25 July 2022
Revised: 14 October 2022
Accepted: 19 September 2023
Published: 13 March 2024
© The author(s) 2023.

Open Access This article is licensed under a Creative Commons Attribution 4.0 International License, which permits use, sharing, adaptation, distribution and reproduction in any medium or format, as long as you give appropriate credit to the original author(s) and the source, provide a link to the Creative Commons licence, and indicate if changes were made.

The images or other third party material in this article are included in the article’s Creative Commons licence, unless indicated otherwise in a credit line to the material. If material is not included in the article’s Creative Commons licence and your intended use is not permitted by statutory regulation or exceeds the permitted use, you will need to obtain permission directly from the copyright holder.

To view a copy of this licence, visit http://creativecommons.org/licenses/by/4.0/.
Return