On-machine inspection and compensation for thin-walled parts with sculptured surface considering cutting vibration and probe posture
(
), Abstract
On-machine inspection has a significant impact on improving high-precision and efficient machining of sculptured surfaces. Due to the lack of machining information and the inability to adapt the parameters to the dynamic cutting conditions, theoretical modeling of profile inspection usually leads to insufficient adaptation, which causes inaccuracy problems. To address the above issues, a novel coupled model for profile inspection is proposed by combining the theoretical model and the data-driven model. The key process is to first realize local feature extraction based on the acquired vibration signals. The hybrid sampling model, which fuses geometric feature terms and vibration feature terms, is modeled by the lever principle. Then, the weight of each feature term is adaptively assigned by a multi-objective multi-verse optimizer. Finally, an inspection error compensation model based on the attention mechanism considering different probe postures is proposed to reduce the impact of pre-travel and radius errors on inspection accuracy. The anisotropy of the probe system error and its influence mechanism on the inspection accuracy are analyzed quantitatively and qualitatively. Compared with the previous models, the proposed hybrid profile inspection model can significantly improve the accuracy and efficiency of on-machine sampling. The proposed compensation model is able to correct the inspection errors with better accuracy. Simulations and experiments demonstrate the feasibility and validity of the proposed methods. The proposed model and corresponding new findings contribute to high-precision and efficient on-machine inspection, and help to understand the coupling mechanism of inspection errors.
References
Jabbar A, Jamshed M A, Abbasi Q, Imran M A and Ur-Rehman M 2023 Leveraging the role of dynamic reconfigurable antennas in viewpoint of industry 4.0 and beyond Research 6 0110
Soori M and Asmael M 2023 Minimization of deflection error in five axis milling of impeller blades Facta Univ. Ser.: Mech. Eng. 21 175–90
Yan B L, Hao Y P, Zhu L D and Liu C F 2022 Towards high milling accuracy of turbine blades: a review Mech. Syst. Signal Process. 170 108727
Huang F Q and Jin X L 2021 Surface texture generation using high-feed milling with spindle speed modulation Precis. Eng. 72 13–24
Quintana G and Ciurana J 2011 Chatter in machining processes: a review Int. J. Mach. Tools Manuf. 51 363–76
Hao Y P, Zhu L D, Yan B L, Qin S Q, Cui D Y and Lu H 2022 Milling chatter detection with WPD and power entropy for Ti-6Al-4V thin-walled parts based on multi-source signals fusion Mech. Syst. Signal Process. 177 109225
Marousi M, Rimpault X, Turenne S and Balazinski M 2023 Initial tool wear and process monitoring during titanium metal matrix composite machining (TiMMC) J. Manuf. Process. 86 208–20
Wang R Q, Song Q H, Peng Y Z, Qin J, Liu Z Q and Liu Z J 2023 Self-adaptive fusion of local-temporal features for tool condition monitoring: a human experience free model Mech. Syst. Signal Process. 195 110310
Sepahi-Boroujeni S, Mayer J R R and Khameneifar F 2020 Repeatability of on-machine probing by a five-axis machine tool Int. J. Mach. Tools Manuf. 152 103544
Lv Z H 2023 Digital twins in industry 5.0 Research 6 0071
Zhuang Q X, Wan N, Guo Y H, Zhu G X and Qian D 2024 A state-of-the-art review on the research and application of on-machine measurement with a touch-trigger probe Measurement 224 113923
Ding D W, Ding W F, Huang R, Fu Y C and Xu F Y 2023 Research progress of laser triangulation on-machine measurement technology for complex surface: a review Measurement 216 113001
Wang W Z, He Y H, Liao R Y, Cai Y Q, Zheng X and Zhao Y 2022 Functional healthy state evaluation approach for manufacturing systems considering imperfect inspection based on extended stochastic flow network J. Manuf. Syst. 64 170–80
Zhu Q Y, Zhang Y X, Luan J B and Hu L H 2022 A machine vision development framework for product appearance quality inspection Appl. Sci. 12 11565
Zhao W Z, Liu Y H, Li Y Z, Hu C W and Sun R 2023 Multi-robot coverage path planning for dimensional inspection of large free-form surfaces based on hierarchical optimization Int. J. Adv. Manuf. Technol. 127 5471–86
Zhang B Y, Feng P F, Sun Z, Cheng X, Zeng L and Fan C R 2023 Efficient sampling method based on co-kriging for free-form surface measurement Precis. Eng. 84 136–47
Yin Z Y, Liu H A, Zhao L J, Cheng J, Tan C, Li X T, Chen Y K, Lin Z Y and Chen M J 2023 Efficient and precise detection for surface flaws on large-aperture optics based on machine vision and machine learning Opt. Laser Technol. 159 109011
Yan Y C, He G Y, Sang Y C, Yao C L, Wang S T and Chen F Z 2022 A two-module automated scanning inspection planning methodology for complex surfaces on coordinate measuring machine Measurement 202 111827
Abdulhameed O, Mian S H, Al-Ahmari A and Alkhalefah H 2020 Patch and curvature specific estimation of efficient sampling scheme for complex surface inspection Int. J. Adv. Manuf. Technol. 110 3407–22
Badar M A, Raman S and Pulat P S 2005 Experimental verification of manufacturing error pattern and its utilization in form tolerance sampling Int. J. Mach. Tools Manuf. 45 63–73
Obeidat S M and Raman S 2011 Process-guided coordinate sampling of end-milled flat plates Int. J. Adv. Manuf. Technol. 53 979–91
Obeidat S M and Raman S 2009 An intelligent sampling method for inspecting free-form surfaces Int. J. Adv. Manuf. Technol. 40 1125–36
Zhang K D, Zhao B L, Zhang W H, Wu X Q and Chen Y H 2022 Efficient adaptive surface measurement based on multilevel gaussian process modeling and scanning path optimization IEEE Trans. Instrum. Meas. 71 1005111
He G Y, Sang Y C, Pang K R and Sun G M 2018 An improved adaptive sampling strategy for freeform surface inspection on CMM Int. J. Adv. Manuf. Technol. 96 1521–35
Guo F Y, Zhang X D, Zou F, Liu J H and Wang Z Q 2019 An adaptive sampling methodology for measuring blades with CMM based on dominant feature points Meas. Sci. Technol. 30 045007
Cheng X, Liu X P, Feng P F, Zeng L, Jiang H Y, Sun Z and Zhang S Q 2022 Efficient adaptive sampling methods based on deviation analysis for on-machine inspection Measurement 188 110497
Zhao Z C, Li Y and Fu Y C 2022 Collision-free path planning for efficient inspection of free-form surface by using a trigger probe Int. J. Adv. Manuf. Technol. 120 2183–200
Mazur T, Rucki M and Gutsalenko Y 2023 Accuracy analysis of the curved profile measurement with CMM: a case study Facta Univ. Ser.: Mech. Eng. 21 121–35
Shen Y J, Ren J J, Huang N D, Zhang Y, Zhang X Q and Zhu L M 2023 Surface form inspection with contact coordinate measurement: a review Int. J. Extrem. Manuf. 5 022006
Qin S Q, Hao Y P, Zhu L D, Wiercigroch M, Yuan Z H, Shi C L and Cui D Y 2023 CWE identification and cutting force prediction in ball-end milling process Int. J. Mech. Sci. 239 107863
Hao Y P, Zhu L D, Yan B L, Ren T Y, Zhao J Z, Ning X F and Lu H 2023 Stiffness design and multi-objective optimization of machine tool structure based on biological inspiration J. Vib. Control 29 2774–88
Sun Y, Jin L Y, Gong Y D, Wen X L, Yin G Q, Wen Q and Tang B J 2022 Experimental evaluation of surface generation and force time-varying characteristics of curvilinear grooved micro end mills fabricated by EDM J. Manuf. Process. 73 799–814
Wang C Y, Miao H H, Li C Y, Li J Q, Xu M T and Liu Z D 2023 Effect of cutting vibration on the surface quality of commercially pure titanium (TA2) based on rotor dynamics model analysis Int. J. Mech. Mater. Des. 19 241–60
Wang X J and Song Q H 2023 Dynamic analysis and surface morphology prediction for deep cavity turning of bent-blade cutter Int. J. Adv. Manuf. Technol. 129 4435–55
Phan N D M, Quinsat Y and Lartigue C 2019 Optimal scanning strategy for on-machine inspection with laser-plane sensor Int. J. Adv. Manuf. Technol. 103 4563–76
Lim H S, Son S M, Wong Y S and Rahman M 2007 Development and evaluation of an on-machine optical measurement device Int. J. Mach. Tools Manuf. 47 1556–62
Guiassa R and Mayer J R R 2011 Predictive compliance based model for compensation in multi-pass milling by on-machine probing CIRP Ann. 60 391–4
Li S M, Zeng L, Feng P F, Li Y M, Xu C and Ma Y 2019 Accurate compensation method for probe pre-travel errors in on-machine inspections Int. J. Adv. Manuf. Technol. 103 2401–10
Wang H and Jiang X G 2022 Geometric error identification of five-axis machine tools using dual quaternion Int. J. Mech. Sci. 229 107522
Wang L P, Kong X Y, Yu G, Li W T, Li M Y and Jiang A B 2022 Error estimation and cross-coupled control based on a novel tool pose representation method of a five-axis hybrid machine tool Int. J. Mach. Tools Manuf. 182 103955
Onishi S, Ibaraki S, Kato T, Yamaguchi M and Sugimoto T 2022 A self-calibration scheme to monitor long-term changes in linear and rotary axis geometric errors Measurement 196 111183
Osei S, Wang W and Ding Q C 2023 A new method to identify the position-independent geometric errors in the rotary axes of five-axis machine tools J. Manuf. Process. 87 46–53
Guo X P, Yin S H, Shu C S, Wu S H and Liu J 2023 Contact on-machine measurement probe error correction method for optical aspheric surface ultraprecision machining Measurement 214 112731
Li S M, Feng P F, Zeng L, Wang S, Li Y M and Zhang S Q 2021 A rigid-flexible coupling pretravel error model for a touch-trigger probe in an on-machine inspection system Int. J. Adv. Manuf. Technol. 114 2991–3003
Rępalska M and Woźniak A 2022 The share of the probe errors in on-machine measurements Precis. Eng. 75 111–9
Woźniak A and Męczyńska K 2020 Measurement hysteresis of touch-trigger probes for CNC machine tools Measurement 156 107568
Papananias M, McLeay T E, Mahfouf M and Kadirkamanathan V 2022 A Bayesian information fusion approach for end product quality estimation using machine learning and on-machine probing J. Manuf. Process. 76 475–85
Sepahi-Boroujeni S, Mayer J R R, Khameneifar F and Woźniak A 2021 A full-covariance uncertainty assessment in on-machine probing Int. J. Mach. Tools Manuf. 167 103768
El Ghazouali S, Vissiere A, Lafon L F, Bouazizi M L and Nouira H 2022 Optimised calibration of machine vision system for close range photogrammetry based on machine learning J. King Saud Univ.—Comput. Inf. Sci. 34 7406–18
Wang S and Zhao Q L 2022 Development of an on-machine measurement system with chromatic confocal probe for measuring the profile error of off-axis biconical free-form optics in ultra-precision grinding Measurement 202 111825
Xiao Y K, Ge G Y, Feng X B, Yang J G and Du Z C 2022 Analysis and compensation of surface flatness of thin-walled valve body parts Int. J. Adv. Manuf. Technol. 123 1679–93
Iglesias I, Sanchez A and Silva F J G 2024 Robotic path compensation training method for optimizing face milling operations based on non-contact CMM techniques Robot. Comput.-Integr. Manuf. 85 102623
Zhang Y Q, Shen Y J, Zhang W Z, Zhang L, Zhu L M and Zhang Y 2022 Generation of efficient and interference-free scanning path for inspecting impeller on a cylindrical CMM Measurement 198 111352
Irino N, Kobayashi A, Shinba Y, Kawai K, Spescha D and Wegener K 2023 Digital twin based accuracy compensation CIRP Ann. 72 345–8
Osei S, Wei W, Yu J H and Ding Q C 2023 A new effective decoupling method to identify the tracking errors of the motion axes of the five-axis machine tools J. Intell. Manuf. 1–16
Maged A and Xie M 2022 Uncertainty utilization in fault detection using Bayesian deep learning J. Manuf. Syst. 64 316–29
Yoon S, Kim A, Cantwell W J, Yeun C Y, Cho C-S, Byon Y-J and Kim T-Y 2023 Defect detection in composites by deep learning using solitary waves Int. J. Mech. Sci. 239 107882
He C L, Yan J W, Wang S Q, Zhang S, Chen G and Ren C Z 2023 A theoretical and deep learning hybrid model for predicting surface roughness of diamond-turned polycrystalline materials Int. J. Extrem. Manuf. 5 035102
Li Y M, Zeng L, Tang K and Li S M 2019 A dynamic pre-travel error prediction model for the kinematic touch trigger probe Measurement 146 689–704
Cheng M H, Jiao L, Yan P, Jiang H S, Wang R B, Qiu T Y and Wang X B 2022 Intelligent tool wear monitoring and multi-step prediction based on deep learning model J. Manuf. Syst. 62 286–300
Mirjalili S, Mirjalili S M and Hatamlou A 2016 Multi-verse optimizer: a nature-inspired algorithm for global optimization Neural Comput. Appl. 27 495–513
Mirjalili S, Jangir P, Mirjalili S Z, Saremi S and Trivedi I N 2017 Optimization of problems with multiple objectives using the multi-verse optimization algorithm Knowl.-Based Syst. 134 50–71
Zhu L D, Yan B L, Wang Y L, Dun Y C, Ma J and Li C L 2021 Inspection of blade profile and machining deviation analysis based on sample points optimization and NURBS knot insertion Thin-Walled Struct. 162 107540
Borré A, Seman L O, Camponogara E, Stefenon S F, Mariani V C and Dos Santos Coelho L 2023 Machine fault detection using a hybrid CNN-LSTM attention-based model Sensors 23 4512
Deng F Y, Bi Y, Liu Y Q and Yang S P 2022 Remaining useful life prediction of machinery: a new multiscale temporal convolutional network framework IEEE Trans. Instrum. Meas. 71 2516913
Marei M and Li W D 2022 Cutting tool prognostics enabled by hybrid CNN-LSTM with transfer learning Int. J. Adv. Manuf. Technol. 118 817–36
Zhang X Y, Lu X, Li W D and Wang S 2021 Prediction of the remaining useful life of cutting tool using the Hurst exponent and CNN-LSTM Int. J. Adv. Manuf. Technol. 112 2277–99
Li B H, Lu Z H, Jin X L and Zhao L P 2023 Tool wear prediction in milling CFRP with different fiber orientations based on multi-channel 1DCNN-LSTM J. Intell. Manuf. 35 2547–66
京公网安备11010802044758号