AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (6.7 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

Effect of Y substitution on the microstructure, magneto-optical, and thermal properties of (Tb1−xYx)3Al5O12 transparent ceramics

Lixuan Zhang1,2Dianjun Hu1,2Xiao Li1,3Ziyu Liu1,2Chen Hu1Lexiang Wu1Tingsong Li1Dariusz Hreniak4Jiang Li1,2( )
Transparent Ceramics Research Center, Shanghai Institute of Ceramics, Chinese Academy of Sciences, Shanghai 201899, China
Center of Materials Science and Optoelectronics Engineering, University of Chinese Academy of Sciences, Beijing 100049, China
Ganjiang Innovation Academy, Chinese Academy of Sciences, Ganzhou 341000, China
Institute of Low Temperature and Structure Research, Polish Academy of Sciences, Wroclaw 50-422, Poland
Show Author Information

Graphical Abstract

Abstract

Faraday isolators can prevent the front-end system from disturbance and damage caused by a back-reflected beam, so they are important elements in laser systems. As magneto-optical materials are the most important component in Faraday isolators, the studies on magneto-optical materials have attracted much attention these years. Tb3Al5O12 (TAG) ceramics are considered to be one of the most promising magneto-optical materials for visible to near-infrared wavelength band application because of their outstanding comprehensive magneto-optical performance. However, the optical quality of TAG ceramics needs further optimization to meet the application requirements. In this work, high optical quality (Tb1−xYx)3Al5O12 (x = 0, 0.05, 0.1, 0.2, and 0.3) magneto-optical ceramics were fabricated successfully by solid-state reaction sintering combined with hot isostatic pressing (HIP) post-treatment. All the ceramics obtained showed a single garnet phase for different values of x in the range studied. The addition of Y2O3 was found to suppress the secondary phase and improve optical quality significantly. The ceramic samples obtained had clear grain boundaries and possessed the in-line transmittance values of 82.9% at 1064 nm and 82.2% at 633 nm, respectively. The Verdet constants of (Tb1−xYx)3Al5O12 ceramics with x = 0, 0.05, 0.1, 0.2, and 0.3 were −188.1, −175.4, −168.5, −143.0, and −119.9 rad/(T·m), respectively. The thermal conductivity of TAG ceramics was found to be 5.23 W/(m·K) at 25 , and when 20% Y was substituted in place of Tb, the thermal conductivity decreased by only 9.4%.

References

[1]

Maiman TH. Stimulated optical radiation in ruby. Nature 1960, 187: 493–494.

[2]

Mironov EA, Snetkov IL, Starobor AV, et al. A perspective on Faraday isolators for advanced lasers. Appl Phys Lett 2023, 122: 100502.

[3]

Tian F, Ikesue A, Li J. Progress and perspectives on composite laser ceramics: A review. J Eur Ceram Soc 2022, 42: 1833–1851.

[4]

Snetkov I, Li J. Selection of magneto-optical material for a Faraday isolator operating in high-power laser radiation. Magnetochemistry 2022, 8: 168.

[5]

Zhang LX, Hu DJ, Snetkov IL, et al. A review on magneto-optical ceramics for Faraday isolators. J Adv Ceram 2023, 12: 873–915.

[6]

Stevens KT, Schlichting W, Foundos G, et al. Promising materials for high power laser isolators. Laser Tech J 2016, 13: 18–21.

[7]

Yoshida H, Tsubakimoto K, Fujimoto Y, et al. Optical properties and Faraday effect of ceramic terbium gallium garnet for a room temperature Faraday rotator. Opt Express 2011, 19: 15181–15187.

[8]

Palashov OV, Starobor AV, Perevezentsev EA, et al. Thermo-optical studies of laser ceramics. Materials 2021, 14: 3944.

[9]

Hu DJ, Li XY, Zhang LX, et al. Terbium(III) oxide (Tb2O3) transparent ceramics by two-step sintering from precipitated powder. Magnetochemistry 2022, 8: 73.

[10]

Qi HB, Zhou D, Li XH, et al. Fabrication of 4 at% La3+ ion doped (Tb x Lu0.96− x )2O3 transparent ceramics by using NC-PLSH technology and characterisation of their magneto-optical properties. J Eur Ceram Soc 2023, 43: 1156–1160.

[11]

Xin Y, Xu T, Wang YZ, et al. Effect of ZrO2 content on microstructure evolution and sintering properties of (Tb0.7Lu0.3)2O3 magneto-optic transparent ceramics. Magnetochemistry 2022, 8: 175.

[12]

Yakovlev A, Snetkov I, Palashov O. Thermo-optical properties of cryogenically cooled (Tb0.9Y0.1)2O3 ceramics. Opt Commun 2022, 504: 127508.

[13]

Hu DJ, Liu X, Liu ZY, et al. Fabrication of Dy2O3 transparent ceramics by vacuum sintering using precipitated powders. Magnetochemistry 2020, 7: 6.

[14]

Hu DJ, Li XY, Snetkov I, et al. Fabrication, microstructure and optical characterizations of holmium oxide (Ho2O3) transparent ceramics. J Eur Ceram Soc 2021, 41: 759–767.

[15]

Lu B, Cheng HM, Xu XX, et al. Preparation and characterization of transparent magneto-optical Ho2O3 ceramics. J Am Ceram Soc 2019, 102: 118–122.

[16]

Hao YK, Xin XH, Liu L, et al. Growth and characterization of Tb3Sc2Al3O12 magneto-optical crystal. Chin J Lumin 2022, 43: 1070–1077. (in Chinese)

[17]

Snetkov IL. Compensation for thermally induced depolarization in magneto-optical media made of materials with a negative optical anisotropy parameter. IEEE J Quantum Elect 2021, 57: 1–8.

[18]

Wu YH, Feng GQ, Li YX, et al. Fabrication and performance optimization of novel (Tb0.9975R0.0025)3Sc2Al3O12 (R = Pr, Ho, Dy, Eu) magneto-optical transparent ceramics. J Alloys Compd 2023, 950: 169929.

[19]

Vojna D, Duda M, Yasuhara R, et al. Verdet constant of potassium terbium fluoride crystal as a function of wavelength and temperature. Opt Lett 2020, 45: 1683.

[20]

Starobor AV, Mironov EA, Palashov OV, et al. Dispersion of optical and magneto-optical properties in a biaxial TbF3 crystal. Laser Phys Lett 2021, 18: 115801.

[21]

Vasyliev V, Villora EG, Nakamura M, et al. UV–visible Faraday rotators based on rare-earth fluoride single crystals: LiREF4 (RE = Tb, Dy, Ho, Er and Yb), PrF3 and CeF3. Opt Express 2012, 20: 14460–14470.

[22]

Starobor A, Mironov E, Palashov O. High-power Faraday isolator on a uniaxial CeF3 crystal. Opt Lett 2019, 44: 1297–1299.

[23]

Wu Z, Li HF, Zhang ZH, et al. Growth and characterization of CeF3 crystals for magneto-optical application. J Inorg Mater 2023, 38: 296–302. (in Chinese)

[24]

Zhang LX, Li XY, Hu DJ, et al. Fabrication and properties of non-stoichiometric Tb2(Hf1− x Tb x )2O7− x magneto-optical ceramics. J Adv Ceram 2022, 11: 784–793.

[25]

Zhang LX, Li XY, Hu DJ, et al. Transparent non-stoichiometric Tb2.45Hf2O7.68 magneto-optical ceramics with high Verdet constant. Scripta Mater 2021, 204: 114158.

[26]

Aung YL, Ikesue A, Yasuhara R, et al. Optical properties of improved Tb2Hf2O7 pyrochlore ceramics. J Alloy Compd 2020, 822: 153564.

[27]

Zhang LX, Li XY, Hu DJ, et al. Fabrication and properties of transparent Tb2Ti2O7 magneto-optical ceramics. J Eur Ceram Soc 2021, 41: 7208–7214.

[28]

Lai YQ, Lu B, Wang M. Optical properties and Faraday magneto-optical effects of highly transparent novel Tb2Zr2O7 fluorite ceramics. Scripta Mater 2023, 227: 115282.

[29]

Kruk A. Impact of Sm ions on microstructure and magneto-optical effects of Y2O3 ceramics obtained by arc plasma melting. J Phys Conf Ser 2022, 2407: 012009.

[30]

Liu HP, Zhan GX, Wu GH, et al. Improved edge-defined film-fed growth of incongruent-melting Tb3Al5O12 crystal with high magneto-optical and thermal performances. Cryst Growth Des 2019, 19: 1525–1531.

[31]

Li XY, Liu Q, Liu X, et al. Sintering parameter optimization of Tb3Al5O12 magneto-optical ceramics by vacuum sintering and HIP post-treatment. J Am Ceram Soc 2021, 104: 2116–2124.

[32]

Zhang LX, Li XY, Hu DJ, et al. Fine-grained Tb3Al5O12 transparent ceramics prepared by co-precipitation synthesis and two-step sintering. Magnetochemistry 2023, 9: 47.

[33]

Lin H, Zhou SM, Teng H. Synthesis of Tb3Al5O12 (TAG) transparent ceramics for potential magneto-optical applications. Opt Mater 2011, 33: 1833–1836.

[34]

Zheleznov D, Starobor A, Palashov O, et al. High-power Faraday isolators based on TAG ceramics. Opt Express 2014, 22: 2578–2583.

[35]

Starobor A, Palashov O. The temperature dependence of thermooptical properties of magnetooptical TAG ceramics doped with silicon and titanium. Opt Mater 2018, 78: 15–20.

[36]

Hamamoto K, Nishio M, Tokita S, et al. Properties of TAG ceramics at room and cryogenic temperatures and performance estimations as a Faraday isolator. Opt Mater Express 2021, 11: 434–441.

[37]

Furuse H, Yasuhara R, Hiraga K, et al. High Verdet constant of Ti-doped terbium aluminum garnet (TAG) ceramics. Opt Mater Express 2016, 6: 191–196.

[38]

Chen C, Li XL, Feng Y, et al. Optimization of CeO2 as sintering aid for Tb3Al5O12 Faraday magneto-optical transparent ceramics. J Mater Sci 2015, 50: 2517–2521.

[39]

Chen C, Yi XZ, Zhang S, et al. Vacuum sintering of Tb3Al5O12 transparent ceramics with combined TEOS+MgO sintering aids. Ceram Int 2015, 41: 12823–12827.

[40]

Duan PP, Liu P, Xu XD, et al. Fabrication of transparent Tb3Al5O12 ceramics by hot isostatic pressing sintering. J Am Ceram Soc 2017, 100: 2893–2900.

[41]

Dai JW, Pan YB, Xie TF, et al. Highly transparent Tb3Al5O12 magneto-optical ceramics sintered from co-precipitated powders with sintering aids. Opt Mater 2018, 78: 370–374.

[42]

Zhang SY, Liu P, Xu XD, et al. Effect of the MgO on microstructure and optical properties of TAG (Tb3Al5O12) transparent ceramics using hot isostatic pressing. Opt Mater 2018, 80: 7–11.

[43]

Chen J, Lin H, Hao DM, et al. Exaggerated grain growth caused by ZrO2-doping and its effect on the optical properties of Tb3Al5O12 ceramics. Scripta Mater 2019, 162: 82–85.

[44]

Li XY, Zhang LX, Hu DJ, et al. Fabrication and characterizations of Tb3Al5O12-based magneto-optical ceramics. Int J Appl Ceram Tec 2023, 20: 493–499.

[45]

Chen C, Ni Y, Zhou SM, et al. Preparation of (Tb0.8Y0.2)3Al5O12 transparent ceramic as novel magneto-optical isolator material. Chin Opt Lett 2013, 11: 021601-1–021601-3.

[46]

Chen C, Zhou SM, Lin H, et al. Fabrication and performance optimization of the magneto-optical (Tb1− x R x )3Al5O12 (R = Y, Ce) transparent ceramics. Appl Phys Lett 2012, 101: 131908.

[47]

Duan PP, Liu P, Xu XD, et al. Fabrication and properties of (Tb x Y1− x )3Al5O12 transparent ceramics by hot isostatic pressing. Opt Mater 2017, 72: 58–62.

[48]

Aung YL, Ikesue A. Development of optical grade (Tb x Y1− x )3Al5O12 ceramics as Faraday rotator material. J Am Ceram Soc 2017, 100: 4081–4087.

[49]

Shannon RD. Revised effective ionic radii and systematic studies of interatomic distances in halides and chalcogenides. Acta Crystallogr 1976, 32: 751–767.

[50]

Huang XY, Zuo L, Li XY, et al. Fabrication and characterization of Tb3Al5O12 magneto-optical ceramics by solid-state reactive sintering. Opt Mater 2020, 102: 109795.

[51]

Chen J, Zhou SM. Review of magneto-optic materials for high power laser isolators (Invited). Infrared Laser Eng 2020, 49: 20201072.

[52]

Chen J, Tang YR, Chen C, et al. Roles of zirconia-doping in the sintering process of high quality Tb3Al5O12 magneto-optic ceramics. Scripta Mater 2020, 176: 83–87.

[53]

Starobor A, Palashov O, Zhou SM. Thermo-optical properties of terbium-aluminum garnet ceramics doped with silicon and titanium. Opt Lett 2016, 41: 1510–1513.

[54]

Zhang JY, Chen HT, Wang JP, et al. Phase transformation process of Tb2O3 at elevated temperature. Scripta Mater 2019, 171: 108–111.

[55]
Feng XQ. Anti-site defects in YAG and LuAG crystals. J Inorg Mater 2010, 25 : 785–794. (in Chinese)
[56]

Li Z, Liu B, Wang JM, et al. Mechanism of intrinsic point defects and oxygen diffusion in yttrium aluminum garnet: First-principles investigation. J Am Ceram Soc 2012, 95: 3628–3633.

[57]

Patel AP, Stanek CR, Grimes RW. Comparison of defect processes in REAlO3 perovskites and RE3Al5O12 garnets. Phys Status Solidi B 2013, 250: 1624–1631.

[58]

Hao DM, Shao XC, Tang YR, et al. Effect of Si4+ doping on the microstructure and magneto-optical properties of TAG transparent ceramics. Opt Mater 2018, 77: 253–257.

[59]

Dai JW, Li J. Promising magneto-optical ceramics for high power Faraday isolators. Scripta Mater 2018, 155: 78–84.

[60]

Hrabovský J, Kučera M, Paloušová L, et al. Optical characterization of Y3Al5O12 and Lu3Al5O12 single crystals. Opt Mater Express 2021, 11: 1218–1223.

[61]

Wang ZJ, Wang XJ, Zhou GH, et al. Highly transparent yttrium titanate (Y2Ti2O7) ceramics from co-precipitated powders. J Eur Ceram Soc 2019, 39: 3229–3234.

[62]

Zhang LX, Li XY, Hu DJ, et al. Magneto-optical, thermal, and mechanical properties of polycrystalline Tb3Al5O12 transparent ceramics. J Am Ceram Soc 2023, 106: 5311–5321.

[63]

Snetkov IL, Voitovich AV, Palashov OV, et al. Review of Faraday isolators for kilowatt average power lasers. IEEE J Quantum Elect 2014, 50: 434–443.

[64]

Yasuhara R, Snetkov I, Starobor A, et al. Terbium gallium garnet ceramic-based Faraday isolator with compensation of thermally induced depolarization for high-energy pulsed lasers with kilowatt average power. Appl Phys Lett 2014, 105: 241104.

[65]

Dou RQ, Zhang HT, Zhang QL, et al. Growth and properties of TSAG and TSLAG magneto-optical crystals with large size. Opt Mater 2019, 96: 109272.

Journal of Advanced Ceramics
Pages 529-538
Cite this article:
Zhang L, Hu D, Li X, et al. Effect of Y substitution on the microstructure, magneto-optical, and thermal properties of (Tb1−xYx)3Al5O12 transparent ceramics. Journal of Advanced Ceramics, 2024, 13(4): 529-538. https://doi.org/10.26599/JAC.2024.9220875

1367

Views

270

Downloads

3

Crossref

4

Web of Science

4

Scopus

0

CSCD

Altmetrics

Received: 02 January 2024
Revised: 22 February 2024
Accepted: 06 March 2024
Published: 30 April 2024
© The Author(s) 2024.

This is an open access article under the terms of the Creative Commons Attribution 4.0 International License (CC BY 4.0, http://creativecommons.org/licenses/by/4.0/).

Return