Achieving ultrahigh power factor in Mg3(Sb,Bi)2-based thermoelectric alloys sintered by introducing elemental Mg and W
Graphical Abstract
Abstract
Improving the power factor (PF) of thermoelectric materials is crucial for increasing the output power density and broadening practical applications. The near-room-temperature electrical performance of Mg3(Sb,Bi)2-based alloys is hindered due to the presence of Mg vacancies and grain boundary scattering, resulting in a lower power factor. In this study, we introduced excess Mg into Mg3(Sb,Bi)2 alloy during the hot-pressing process, triggering a liquid phase sintering process, which can effectively fill the Mg vacancies and increase the average grain size (Dave) to significantly reduce grain boundary scattering. This leads to enhanced room-temperature electrical conductivity (σ) without detrimental effects on the Seebeck coefficient (S), thus yielding a high average PF of ~25.3 μW·cm−1·K−2 and an average figure of merit (ZT) of ~1.03 within the temperature range of 323‒623 K. Moreover, different amounts of W were further added, and density-functional theory (DFT) calculations reveal that W segregation at grain boundaries (GBs) reduces interfacial potential barriers, leading to improved S and σ. Consequently, an ultrahigh average PF of ~26.2 μW·cm−1·K−2 was attained in the W0.06Mg3.2Sb1.5Bi0.49Te0.01–4% Mg alloys. Additionally, the mechanical properties (Vickers hardness and fracture toughness) were also enhanced compared with those of the pristine Mg3(Sb,Bi)2 alloy. This dual-modified approach can significantly boost the TE performance and mechanical stability, advancing Mg3(Sb,Bi)2-based materials for practical applications.
Electronic Supplementary Material
References
He J, Tritt TM. Advances in thermoelectric materials research: Looking back and moving forward. Science 2017, 357: eaak9997.
Yuan ZL, Wu MY, Han S, et al. Entropy engineering enabled atomically dispersed Cu doping leading to an exceptionally high thermoelectric figure of merit in n-type lead chalcogenides. Energy Environ Sci 2024, 17: 2921–2934.
Mao J, Zhu HT, Ding ZW, et al. High thermoelectric cooling performance of n-type Mg3Bi2-based materials. Science 2019, 365: 495–498.
Yu Y, Cagnoni M, Cojocaru-Mirédin O, et al. Chalcogenide thermoelectrics empowered by an unconventional bonding mechanism. Adv Funct Mater 2020, 30: 1904862.
Zhang CH, Yan G, Wang YB, et al. Grain boundary complexions enable a simultaneous optimization of electron and phonon transport leading to high-performance GeTe thermoelectric devices. Adv Energy Mater 2023, 13: 2203361.
Pei YZ, Wang H, Snyder GJ. Band engineering of thermoelectric materials. Adv Mater 2012, 24: 6125–6135.
Xu PF, Jin KP, Yu Y, et al. High-performance Bi2Te3-based thermoelectrics enabled by ≈ 1 nm metal chalcogenide clusters with size-dependent electron and phonon structures. Adv Funct Mater 2024, 34: 2401240.
Yan X, Pan HJ, Zhang YX, et al. Highly enhanced thermoelectric and mechanical performance of copper sulfides via natural mineral in-situ phase separation. J Adv Ceram 2024, 13: 641–651.
Wu RG, Yu Y, Jia S, et al. Strong charge carrier scattering at grain boundaries of PbTe caused by the collapse of metavalent bonding. Nat Commun 2023, 14: 719.
Chen C, Wang BH, Chen C, et al. Greatly enhanced mechanical properties of thermoelectric SnSe through microstructure engineering. J Adv Ceram 2023, 12: 1081–1089.
Liu ZY, Wang YG, Yang T, et al. Alloying engineering for thermoelectric performance enhancement in p-type skutterudites with synergistic carrier concentration optimization and thermal conductivity reduction. J Adv Ceram 2023, 12: 539–552.
Zhu HT, Mao J, Li YW, et al. Discovery of TaFeSb-based half-Heuslers with high thermoelectric performance. Nat Commun 2019, 10: 270.
Zhou CJ, Yu Y, Lee YL, et al. Exceptionally high average power factor and thermoelectric figure of merit in n-type PbSe by the dual incorporation of Cu and Te. J Am Chem Soc 2020, 142: 15172–15186.
Zhang JW, Song LR, Pedersen SH, et al. Discovery of high-performance low-cost n-type Mg3Sb2-based thermoelectric materials with multi-valley conduction bands. Nat Commun 2017, 8: 13901.
Li AR, Hu CL, He B, et al. Demonstration of valley anisotropy utilized to enhance the thermoelectric power factor. Nat Commun 2021, 12: 5408.
Li J, Zhang S, Jia F, et al. Point defect engineering and machinability in n-type Mg3Sb2-based materials. Mater Today Phys 2020, 15: 100269.
Shuai J, Ge BH, Mao J, et al. Significant role of Mg stoichiometry in designing high thermoelectric performance for Mg3(Sb,Bi)2-based n-type zintls. J Am Chem Soc 2018, 140: 1910–1915.
Tamaki H, Sato HK, Kanno T. Isotropic conduction network and defect chemistry in Mg3+ δ Sb2-based layered zintl compounds with high thermoelectric performance. Adv Mater 2016, 28: 10182–10187.
Mao J, Shuai J, Song SW, et al. Manipulation of ionized impurity scattering for achieving high thermoelectric performance in n-type Mg3Sb2-based materials. P Natl Acad Sci USA 2017, 114: 10548–10553.
Mao J, Wu YX, Song SW, et al. Defect engineering for realizing high thermoelectric performance in n-type Mg3Sb2-based materials. ACS Energy Lett 2017, 2: 2245–2250.
Liang JS, Shi XL, Peng Y, et al. Synergistic effect of band and nanostructure engineering on the boosted thermoelectric performance of n-type Mg3+ δ (Sb,Bi)2 Zintls. Adv Energy Mater 2022, 12: 2201086.
Chen XX, Wu HJ, Cui J, et al. Extraordinary thermoelectric performance in n-type manganese doped Mg3Sb2 Zintl: High band degeneracy, tuned carrier scattering mechanism and hierarchical microstructure. Nano Energy 2018, 52: 246–255.
Song SW, Mao J, Bordelon M, et al. Joint effect of magnesium and yttrium on enhancing thermoelectric properties of n-type Zintl Mg3+ δ Y0.02Sb1.5Bi0.5. Mater Today Phys 2019, 8: 25–33.
Wu L, Zhou ZZ, Han G, et al. Realizing high thermoelectric performance in p-type CaZn2Sb2-alloyed Mg3Sb2-based materials via band and point defect engineering. Chem Eng J 2023, 475: 145988.
Yang KK, Li XY, Sun CL, et al. Robust room temperature thermoelectric performance of Mg3(Sb,Bi)2-based alloys via multivalent Mn doping. Adv Funct Mater 2024, 34: 2315886.
Hu CL, Xia KY, Fu CG, et al. Carrier grain boundary scattering in thermoelectric materials. Energy Environ Sci 2022, 15: 1406–1422.
Shi XM, Zhao TT, Zhang XY, et al. Extraordinary n-type Mg3SbBi thermoelectrics enabled by yttrium doping. Adv Mater 2019, 31: 1903387.
Chen N, Zhu HT, Li GD, et al. Improved figure of merit ( z) at low temperatures for superior thermoelectric cooling in Mg3(Bi,Sb)2. Nat Commun 2023, 14: 4932.
Kanno T, Tamaki H, Sato HK, et al. Enhancement of average thermoelectric figure of merit by increasing the grain-size of Mg3.2Sb1.5Bi0.49Te0.01. Appl Phys Lett 2018, 112: 033903.
Wood M, Kuo JJ, Imasato K, et al. Improvement of low-temperature zT in a Mg3Sb2–Mg3Bi2 solid solution via Mg-vapor annealing. Adv Mater 2019, 31: 1902337.
Luo T, Kuo JJ, Griffith KJ, et al. Nb-mediated grain growth and grain-boundary engineering in Mg3Sb2-based thermoelectric materials. Adv Funct Mater 2021, 31: 2100258.
Liu ZH, Sato N, Gao WH, et al. Demonstration of ultrahigh thermoelectric efficiency of ~7.3% in Mg3Sb2/MgAgSb module for low-temperature energy harvesting. Joule 2021, 5: 1196–1208.
Wang LQ, Sato N, Peng Y, et al. Realizing high thermoelectric performance in N-type Mg3(Sb,Bi)2-based materials via synergetic Mo addition and Sb–Bi ratio refining. Adv Energy Mater 2023, 13: 2301667.
Roudebush JH, Toberer ES, Hope H, et al. Crystal structure, characterization and thermoelectric properties of the type-I clathrate Ba8− y Sr y Al14Si32 (0.6 ≤ y ≤ 1.3) prepared by aluminum flux. J Solid State Chem 2011, 184: 1176–1185.
Agne MT, Imasato K, Anand S, et al. Heat capacity of Mg3Sb2, Mg3Bi2, and their alloys at high temperature. Mater Today Phys 2018, 6: 83–88.
Yang J, Ye HL, Zhang XZ, et al. Dual-site doping and low-angle grain boundaries lead to high thermoelectric performance in N-type Bi2S3. Adv Funct Mater 2024, 34: 2306961.
Yu L, Shi XL, Mao YQ, et al. Advancing n-type Mg3+ δ Sb1.5Bi0.47Te0.03-based thermoelectric Zintls via Sc-doping-driven band and defect engineering. Chem Eng J 2024, 482: 149051.
Kresse G, Joubert D. From ultrasoft pseudopotentials to the projector augmented-wave method. Phys Rev B 1999, 59: 1758–1775.
Perdew JP, Burke K, Ernzerhof M. Generalized gradient approximation made simple. Phys Rev Lett 1996, 77: 3865–3868.
Okamoto H. Mg–Sb (magnesium–antimony). J Phase Equilib Diffus 2010, 31: 574.
Perrière C, Boulesteix R, Maître A, et al. Study of sintering mechanisms of Ca-doped yttrium aluminum garnet ceramics: From nanostructure to macroscopic behaviour. J Eur Ceram Soc 2023, 43: 565–575.
Jørgensen LR, Zhang JW, Zeuthen CB, et al. Thermal stability of Mg3Sb1.475Bi0.475Te0.05 high performance n-type thermoelectric investigated through powder X-ray diffraction and pair distribution function analysis. J Mater Chem A 2018, 6: 17171–17176.
German RM, Suri P, Park SJ. Review: Liquid phase sintering. J Mater Sci 2009, 44: 1–39.
Wang DD, Xing MB, Wei YY, et al. Modeling of nucleation and growth in the synthesis of PbS colloidal quantum dots under variable temperatures. ACS Omega 2021, 6: 3701–3710.
Talapin DV, Rogach AL, Haase M, et al. Evolution of an ensemble of nanoparticles in a colloidal solution: theoretical study. J Phys Chem B 2001, 105: 12278–12285.
Lei JD, Zhao KP, Liao JC, et al. Approaching crystal’s limit of thermoelectrics by nano-sintering-aid at grain boundaries. Nat Commun 2024, 15: 6588.
Zhao LJ, Yu LH, Yang J, et al. Enhancing thermoelectric and mechanical properties of p-type Cu3SbSe4-based materials via embedding nanoscale Sb2Se3. Mater Chem Phys 2022, 292: 126669.
Shi XM, Sun C, Bu ZL, et al. Revelation of inherently high mobility enables Mg3Sb2 as a sustainable alternative to n-Bi2Te3 thermoelectrics. Adv Sci 2019, 6: 1802286.
Yu L, Shi XL, Mao YQ, et al. Simultaneously boosting thermoelectric and mechanical properties of n-type Mg3Sb1.5Bi0.5-based zintls through energy-band and defect engineering. ACS Nano 2024, 18: 1678–1689.
Kumari N, Pai N, Chavan V, et al. Strained lamellar structures leading to improved thermoelectric performance in Mg3Sb1.5Bi0.5. ACS Appl Mater Inter 2023, 15: 46995–47003.
Kuo JJ, Yu Y, Kang SD, et al. Mg deficiency in grain boundaries of n-type Mg3Sb2 identified by atom probe tomography. Adv Mater Interfaces 2019, 6: 1900429.
Tan C, Abbas A, Wang HX, et al. Optimizing grain boundary potential barriers for enhanced thermoelectric performance of NbFeSb alloy. Cell Rep Phys Sci 2024, 5: 101799.
Kuo JJ, Kang SD, Imasato K, et al. Grain boundary dominated charge transport in Mg3Sb2-based compounds. Energy Environ Sci 2018, 11: 429–434.
Kumari N, Dasgupta T. Developing contacting solutions for n-type Mg3Sb1.5Bi0.5 based thermoelectric materials. J Alloys Compd 2023, 944: 169220.
Imasato K, Fu CG, Pan Y, et al. Metallic n-type Mg3Sb2 single crystals demonstrate the absence of ionized impurity scattering and enhanced thermoelectric performance. Adv Mater 2020, 32: 1908218.
Jin M, Lin SQ, Li W, et al. Nearly isotropic transport properties in anisotropically structured n-type single-crystalline Mg3Sb2. Mater Today Phys 2021, 21: 100508.
Snyder GJ, Snyder AH, Wood M, et al. Weighted mobility. Adv Mater 2020, 32: 2001537.
Li F, Liu X, Ma N, et al. Thermoelectric zintl compound In1− x Ga x Te: Pure acoustic phonon scattering and dopant-induced deformation potential reduction and lattice shrink. Angew Chem Int Ed 2022, 61: e202208216.
Shuai J, Mao J, Song SW, et al. Tuning the carrier scattering mechanism to effectively improve the thermoelectric properties. Energy Environ Sci 2017, 10: 799–807.
Li JW, Han ZJ, Yu JC, et al. Wide-temperature-range thermoelectric n-type Mg3(Sb,Bi)2 with high average and peak zT values. Nat Commun 2023, 14: 7428.
Manimozhi T, Kavirajan S, Navaneethan M. Synergistic effect of energy filtering, modulation doping and boundary scattering of multiphase Cu–Sb–Bi–S system for enhanced thermoelectric performance. Surf Interfaces 2023, 41: 103224.
Shang HJ, Zou Q, Zhang L, et al. Improving thermal stability and revealing physical mechanism in n-type Mg3Sb2− x Bi x for practical applications. Nano Energy 2023, 109: 108270.
Wu XZ, Han ZJ, Zhu YB, et al. A general design strategy for thermoelectric interface materials in n-type Mg3Sb1.5Bi0.5 single leg used in TEGs. Acta Mater 2022, 226: 117616.
Shu R, Zhou YC, Wang Q, et al. Mg3+ δ Sb x Bi2− x family: A promising substitute for the state-of-the-art n-type thermoelectric materials near room temperature. Adv Funct Mater 2019, 29: 1807235.
Wang MJ, Zhang GW, Xu H, et al. Investigation on Mg3Sb2/Mg2Si heterogeneous nucleation interface using density functional theory. Materials 2020, 13: 1681.
Yang L, Bergstrom ZJ, Wirth BD. First-principles study of stability of helium-vacancy complexes below tungsten surfaces. J Appl Phys 2018, 123: 205108.
Qiu YD, Xu SJ, Zhang XZ, et al. Reactive air wetting and brazing of Al2O3 ceramics using Ag–Nb2O5 filler: Performance and interfacial behavior. J Adv Ceram 2024, 13: 135–142.
Yang J, Wang MY, Lu BB, et al. Boosting the power factor and thermoelectric performance in eco-friendly Cu3SbS4 by twin boundary and grain boundary phase. Chem Eng J 2023, 468: 143559.
Tian BZ, Ma HS, An X, et al. Multifunctional durable solid-state thermoelectric sensor enabled by interstitial Co doping in Mg3(Sb,Bi)2. Device 2024, 2: 100524.
Zhang CH, Geng XJ, Chen B, et al. Boron-mediated grain boundary engineering enables simultaneous improvement of thermoelectric and mechanical properties in N-type Bi2Te3. Small 2021, 17: 2104067.
Male JP, Abdellaoui L, Yu Y, et al. Dislocations stabilized by point defects increase brittleness in PbTe. Adv Funct Mater 2021, 31: 2108006.
Wang HY, Han G, Zhang B, et al. AgSbSe2 inclusions enabling high thermoelectric and mechanical performance in n-type Ag2Se-based composites. Acta Mater 2023, 248: 118753.
Ma C, Bai X, Ren Q, et al. From microstructure evolution to thermoelectric and mechanical properties enhancement of SnSe. J Mater Sci Technol 2020, 58: 10–15.
京公网安备11010802044758号