AI Chat Paper
Note: Please note that the following content is generated by AMiner AI. SciOpen does not take any responsibility related to this content.
{{lang === 'zh_CN' ? '文章概述' : 'Summary'}}
{{lang === 'en_US' ? '中' : 'Eng'}}
Chat more with AI
PDF (3.9 MB)
Collect
Submit Manuscript AI Chat Paper
Show Outline
Outline
Show full outline
Hide outline
Outline
Show full outline
Hide outline
Research Article | Open Access

Sensitivity of Nanostructured Mn-Doped Cobalt Oxide Films for Gas Sensor Application

Ehssan Salah Hassan1Kameran Yasseen Qader2Esraa Hassn Hadi2Sami Salman Chiad2Nadir Fadhil Habubi2( )Khalid Haneen Abass3( )
Department of Physics, College of Science, Mustansiriyah University, Baghdad, Iraq
Department of Physics, College of Education, Mustansiriyah University, Baghdad, Iraq
Department of Physics, College of Education for Pure Sciences, University of Babylon, Iraq
Show Author Information

Abstract

The effect of manganese doped cobalt oxide (Co3O4:Mn) was investigated by two different ratios (1% and 3%), which were precipitated by spray pyrolysis technique (SPT), and was adopted using a laboratory designed glass atomizer. Glass substrates were used to deposit films on them, heated at a temperature of 420 ℃. The structural properties were studied through X-ray diffraction. The results showed that all deposit nanostructured films were polycrystalline and there was a decrease in the preferred reflection intensity along (311) plane resulting in a decrease in the crystallite size. Surface properties were analyzed through atomic force microscopy (AFM), which showed a decrease in the roughness and the particle size growth was a vertical columnar rod. The optical characterization displayed that the transmittance of pure Co3O4 nanostructured films was 48% and decreased to 35% for 1% of the Mn concentration, and continued to decrease to 33% with the increase of manganese concentration up to 3%. Optical energy bandgap of pure Co3O4 nanostructured films was 1.435 eV and decreased to 1.419 eV for 1% of Mn concentration, and continued to decrease to 1.367 eV with the increase of Mn concentration up to 3%. The highest percentage sensitivity was for the sample doped with 3% Mn, which was about 65%, for NO2 gas concentration of 600 ppm, at an operating temperature of 200 ℃.

References

[1]

M. Basit, N. Shah, S. Ali, et al., Cobalt Doping Effects on Zinc Oxide Transparent Conducting Thin Films. World Applied Sciences Journal, 2014, 32(8): 1664-1670.

[2]

S.S. Chiad, H.A. Noor, O.M. Abdulmunem, et al., Optical and Structural properties of Ni-doped Co3O4 Nanostructure Thin films Via CSPM. IOP Conf. Series: Journal of Physics: Conf. Series 1362, 2019: 012115.

[3]

K. Sugiura, H. Ohta, K. Nomura, et al., Thermo-electric properties of epitaxial films of layered cobalt oxidesfabricated by topotactic ion-exchange methods. International Conference on Thermoelectrics, IEEE, 2006, 1: 4244-0811.

[4]

G. Calin, M. Irimia, C. Scarlat, et al., Synthesis and characterization of nickel cobalt oxide thin films. CAS 2010 Proceedings (International Semiconductor Conference), 2010, 978(1): 4244-5781.

[5]

R. Chikwenze, P. Nwofe, P. Agbo, et al., Annealing effects and film thickness dependence of cobalt selenide thin films grown by the chemical bath deposition method. IOSR-JECE, 2015, 10(5): 19-24.

[6]

İ. Kariper, T. Özpozan, Optical properties of cobalt xanthate films on different substrates. International Journal of Minerals, Metallurgy and Materials, 2014, 21(7): 736-740.

[7]

G. Kandalkar, C. Lokhande, R. Mane et al., A non-thermal chemical synthesis of hydrophilic and amorphous cobalt oxide films for super capacitor application. Applied Surface Science, 2007, 253: 3952-3956.

[8]

M. Rad, M.T. Aan, and M. Alavi, Effect of incubation time, CuSO4 and Glucose concentrations on biosynthesis of copper oxide (CuO) nanoparticles with rectangular shape and antibacterial activity: Taguchi method approach. Nano Biomed. Eng., 2018, 10(1) : 25-33.

[9]

M. Alavi, M. Rai, Recent advances in antibacterial applications of metal nanoparticles (MNPs) and metal nanocomposites (MNCs) against multi drug resistant (MDR) bacteria. Expert Review of Anti-infective Therapy, 2019.

[10]

M. Alavi, N. Karimi, Biosynthesis of Ag and Cu NPs by secondary metabolites of usnicacid and thymol with biological macromolecules aggregation and antibacterial activities against multi drug resistant (MDR) bacteria. Int J Biol Macromol., 2019, 1: 128: 893-901.

[11]

G. Kandalkar, L. Hae-Min, C Heeyeop et al., Structural, morphological, and electrical characteristics of the electro deposited cobalt oxide electrode for super capacitor applications. Materials Research Bulletin, 2011, 46: 48-51.

[12]

R. Gupta, K. Ghosh, and P. Kahol, Room temperature ferromagnetic multilayer thin film based on indium oxide and iron oxide for transparent spintronic applications. Materials Letters, 2010, 64: 2022-2024.

[13]

K. Ravichandran, K. Karthika, B. Sakthivel, et al., Tuning the combined magnetic and antibacterial properties of ZnO nanopowders through Mn doping for biomedical applications. Journal of Magnetism and MagneticMaterials, 2014, 358(359): 50-55.

[14]

M. Dervin, I. Buret, and C. Loisel, Easy-to-Deploy Emergency Communication System Based on a Transparent Telecommunication Satellite. First International Conference on Advances in Satellite and Space Communications IEEE, 2009, 168-173.

[15]
S. Pocoví-Martínez, I. Zumeta-Dube, and D. Diaz, Production of Methanol from Aqueous CO2 by Using Co3O4 Nanostructures as Photocatalysts, Journal of Nanomaterials Volume. Article ID, 2019, 6461493, 10, https://doi.org/10.1155/2019/6461493
[16]

S. Kandalkar, J. Gunjakar, and C. Lokhande, Preparation of cobalt oxide thin films and its use in super capacitor application. Applied Surface Science, 2008, 254: 5540-5544.

[17]

S. Mu, Z. Wu, Y. Wang, et al., Formation and characterization of cobalt oxide layers on polyimide films via surface modification and ion-exchange technique. Thin Solid Films, 2010, 518: 4175-4182.

[18]

J. Tyczkowski, R. Kapica, and J. Łojewska, Thin cobalt oxide films for catalysis deposited by plasma-enhanced metal–organic chemical vapor deposition. Thin Solid Films, 2007, 515: 6590-6595.

[19]
A. Jayatissa, K. Guoa, A. Jayasuriya, et al., Fabrication of nanocrystalline cobalt oxide via sol-gel coating. Materials Science and Engineering, 2007, B, 144: 69-72.
[20]

S. Jogade, D. Sutrave, and V. Patil, Structural and Morphological Properties of Mn Doped Co3O4 ThinFilm Deposited by Spin Coat Method. Int. Engineering Research and Application, 2016, 6(9): 41-46.

[21]

J. Shan, R. Dai, Cobalt oxide thin film prepared by an electrochemical route for Li-ion battery. Journal of Power Sources, 2009, 189: 204-210.

[22]

A. Balati, Heterojunction of TiO2 nanoparticle embedded into ZSM5 to 2D and 3D layered structures of MoS2 nanosheets fabricated by pulsed laser ablation and microwave technique in deionized water: structurally enhanced photocatalytic performance. Applied Nanoscience, 2018: 1-14.

[23]

A. Balati, S. Tek, K. Nash, et al., Nanoarchitecture of TiO2 microspheres with expanded lattice interlayers and its heterojunction to the laser modified black TiO2 using pulsed laser ablation in liquid with improved photocatalytic performance under visible light irradiation. Journal of Colloid and Interface Science, 2019, 541: 234-248.

[24]

A. Balati, B. Arianne, A. Shahriar, et al., Simultaneous formation of ultra-thin MoSe2 nanosheets, Inorganic Fullerene-Like MoSe2 and MoO3 quantum dots using fast and ecofriendly Pulsed Laser Ablation in Liquid followed by microwave treatment. Materials Science in Semiconductor Processing, 2019, 99: 68-77.

[25]

A. Kaphle, T. Reed, A. Apblett, et al., Doping Efficiency in Cobalt-Doped ZnO Nanostructured Materials. Journal of Nanomaterials, 2019, 2019: 1-13.

[26]

R. Venkatesh, C.R. Dhas, R. Sivakumar, et al., Analysis of optical dispersion parameters and electrochromic properties of manganese-doped Co3O4 dendrite structured thin films. Journal of Physics and Chemistry of Solids, 2018, 122: 118-129.

[27]

A. Saroja, I. Punithavathy, S. Jeyakumar et al., Substrate temperature influence on the optical and electrical properties of spray deposited Sn2S3 thin films. Optik130, 2017: 245-225

[28]

S. Petitto, E. Marsh, G. Carson, et al., Cobalt oxide surface chemistry: The interaction of CoO (1 0 0), Co3O4 (1 1 0) and Co3O4 (1 1 1) with oxygen and water, Journal of Molecular Catalysis A: Chemical, 2008, 281: 49-58.

[29]

K. Abass, M. Mohammed, Fabrication of ZnO: Al/Si Solar Cell and Enhancement its Efficiency Via Al-Doping, Nano Biomed. Eng. , 2019, 11(2): 170-177.

[30]

C. Guyon, A. Barkallah, F. Rousseau,, et al., Deposition of cobalt oxide thin films by plasma-enhanced chemical vapor deposition (PECVD) for catalytic applications. Surface & Coatings Technology, 2011, 206: 1673-1679.

[31]

E. Hassan, T. Mubarak, K. Abass, et al., Structural, Morphological and Optical Characterization of Tin Doped Zinc Oxide Thin Film by (SPT). Journal of Physics: Conference Series, 2019: 1234.

[32]

C. Liao, Y. Lee, H. Yu, et al., Structure characterization and electrochemical properties of RF sputtered lithium nickel cobalt oxide thin films. Electrochimica 50, 2004: 461-466.

[33]
A. Khadayeir, E. Hassan, S. Chiad, et al., Structural and Optical Properties of Boron Doped Cadmium Oxide. 2019, Journal of Physics: Conference Series, 1234.
[34]
S. Shi, S. Qian, X. Hou, et al., Structural and Optical Properties of Amorphous Al2O3 Thin Film Deposited by Atomic Layer Deposition. 2019, Advances in Condensed Matter Physics, 2018: Article ID 7598978 10 pages.
[35]

L. Qiao, H.Y. Xiao, H.M. Meyer, et al., Nature of the band gap and origin of the electro/ photoactivity of Co3O4. J. Mater. Chem. C, 2013, 1: 46284633.

[36]

R. Shinde, S. Mahadik, T. Guja, et al., Super capacitive cobalt oxide (Co3O4) thin films by spray pyrolysis. Applied Surface Science, 2006, 252: 7487-7492.

[37]

M. Pal, U. Pal, J. M. Gracia, et al., Effects of crystallization and dopant concentration on the emission behavior of TiO2: Eu nanophosphors. Nanoscale Research Letters, 2012, 7: 1-12.

[38]

V. Patil, P. Joshi, M. Chougule, et al., Synthesis and Characterization of Co3O4 Thin Film. Soft Nanoscience Letters, 2012, 2: 1-7.

[39]

A. Alkelaby, K. Abass, T. Mubarak, et al., Effect of MnCl2 Additive on Optical and Dispersion Parameters of Poly methyl Methacrylate Films. Journal of Global Pharma Technology, 2019, 11(4): 347-352.

[40]

D. Latif, S. Chiad, M. Erhayief, et al., Effects of FeCl3 additives on optical parameters of PVA. Journal of Physics: Conf. series, 2018: 1003.

[41]

P. Prathap, Y. Subbaiah, M. Devika, et al., Optical properties of In2O3 films prepared by spray pyrolysis. Materials Chemistry and Physics, 2006, 100(2-3): 10, 375-379.

[42]

P. Rambu, D. Sirbu, N. Iftimie, et al., Polycrystalline ZnO-In2O3 thin films as gas sensors. Thin Solid Films, 2011, 520: 1303-1307.

[43]

A.A. Alharbi, U. Weimar, and N. Bârsan, Gas Sensing Mechanism Investigation of LaFeO3 Perovskite-Type Oxides via Operando Technique. Proceedings, 2019, 14: 51.

Nano Biomedicine and Engineering
Pages 205-213
Cite this article:
Hassan ES, Qader KY, Hadi EH, et al. Sensitivity of Nanostructured Mn-Doped Cobalt Oxide Films for Gas Sensor Application. Nano Biomedicine and Engineering, 2020, 12(3): 205-213. https://doi.org/10.5101/nbe.v12i3.p205-213

800

Views

50

Downloads

28

Crossref

36

Scopus

Altmetrics

Received: 19 March 2020
Accepted: 20 June 2020
Published: 13 July 2020
© Ehssan Salah Hassan, Kameran Yasseen Qader, Esraa Hassn Hadi, Sami Salman Chiad, Nadir Fadhil Habubi, and Khalid Haneen Abass.

This is an open-access article distributed under the terms of the Creative Commons Attribution License, which permits unrestricted use, distribution, and reproduction in any medium, provided the original author and source are credited.

Return